ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Programming the Chips And Technologies SVGA Chip ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Written for the PC-GPE by Mark Feldman e-mail address : u914097@student.canberra.edu.au myndale@cairo.anu.edu.au Please read the file SVGINTRO.TXT (Graphics/SVGA/Intro PC-GPE menu option) ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ THIS FILE MAY NOT BE DISTRIBUTED ³ ³ SEPARATE TO THE ENTIRE PC-GPE COLLECTION. ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÚÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ Disclaimer ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÙ I assume no responsibility whatsoever for any effect that this file, the information contained therein or the use thereof has on you, your sanity, computer, spouse, children, pets or anything else related to you or your existance. No warranty is provided nor implied with this information. ÚÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ Setup mode ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÙ To modify some of the CAT's internal SVGA registers the card must be placed into setup mode. This is done by writing the value 1Eh to port 46E8h. To exit setup mode write the value 0Eh to port 46E8h. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ Enabling Extensions ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The CAT's extended registers are normally locked and must be enabled before you attempt to modify them. To enable them, you must enter setup mode, write the value 80h to port 103h and exit setup mode. To disable them you must enter setup mode, write the value 00h to port 103h and exit setup mode. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ Identifying the CAT Chip ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Detecting the presence of a CAT chip can be done by entering setup mode, checking that the value returned from reading port 104h is A5h and then exiting setup mode. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ Identifying which CAT Chip and Revision Number ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The CAT chip type and revision number can be determined by enabling extensions, reading the value of register 0 and disabling extensions. The top 4 bits (4-7) are the chip id and the lower 4 are the version number. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Chip ID Chip ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ 1 82c451 or 82c452 ³ ³ 2 82c455 ³ ³ 3 82c453 ³ ³ 5 82c456 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The 82c451 and 82c452 can be distinguished by attempting to modify register 3Ah (Graphics Cursor Color 1, make sure you set it back to what it was). If the register exists the chip is an 82c452. Alternatively the chip ID can be determined using the Get Controller Information BIOS call (see below). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ CAT Graphics Display Modes ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Mode Resolution Colors Chip ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ 25h 640x480 16 451/452/453 ³ ³ 6Ah 800x600 16 451/452/453 ³ ³ 70h 800x600 16 451/452/453 ³ ³ 71h 960x720 16 452 ³ ³ 72h 1024x768 16 452/453 ³ ³ 78h 640x400 256 451/452/453 ³ ³ 79h 640x480 256 452/453 ³ ³ 7Ah 768x576 256 452 ³ ³ 7Ch 800x600 256 453 ³ ³ 7Eh 1024x768 256 453 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ The CAT Display Memory ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The following registers can only be modified while the extended registers are enabled (See Enabling Extensions above). The 451, 455 and 456 are always in single-paging mode and have 4 64K banks. To switch to a bank you must first enable access to extended memory with the following procedure: Port[$3D6] := $0B; Port[$3D6] := Port[$3D6] and $FD; Selecting a bank can be done with the following procedure: Port[$3D6] := $0B; Port[$3D7] := bank_number; where bank_number = 0 - 3. Each bank is 64K long and has a 86K granularity. The 452 and 453 banks have a 16K granularity, so if you want 64K granularity you must multiply the bank number by 4 before writing it to the registers : Port[$3D6] := $10; Port[$3D7] := bank_number Shl 2; { = bank_numer * 4 } The 452 and 453 allow duel paging. The 64K host address space is split in two, one low area A000:0000-7FFFh and a high area A000:8000-FFFFh. This mode can be enabled with the following procedure: Port[$3D6] := $10; Port[$3D6] := Port[$3D6] or 2; In this mode each bank also has a granularity of 16K. The lower bank is selected with the same procedure for setting the bank in single-paging mode. The upper bank is selected with the following call: Port[$3D6] := $11; Port[$3D7] := bank_number Shl 2; { = bank_numer * 4 } None of the CAT chips allow you to select one bank for reading and another for writing. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³ CAT Get Controller Information BIOS Call ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Int 10h Inputs : AH = 5Fh Extended VGA Control AL = 00h Get Controller Information Returns: AL = 5Fh Extended VGA control function supported BL = Chip type bits 7-4 contain the chip type number 0 = 82c451 1 = 82c452 2 = 82c455 ? = 82c453 bits 3-0 contain the revision number BH = Memory Size Video memory size 0 = 256k 1 = 512k 2 = 1M